StillSmart

Re: T500 water outlet problem

2013-04-20T00:49:38+00:00

You will be very happy with this setup. I'm very pleased with mine. This be where i got mine http://www.homebrewing.org/Home-Distilling-Equipment_c_264.html Now more i use it more better it gets & more over all outcome get better. The biggest technique will be your wash.

Statistics: Posted by lll_0_mike_0_lll — Sat Apr 20, 2013 12:49 am

Re: T500 water outlet problem

2013-04-20T00:08:05+00:00

Thanks for threhelp mike! A few days ago I called the shop where I bought it from and the owner sent me a return label so he can see for himself. He check it out and said there was something definitely wrong and over nighted a brand new column. Adventures in home brewing in Michigan really has top notch cust service!

Statistics: Posted by nitronick60 — Sat Apr 20, 2013 12:08 am

Re: T500 water outlet problem

2013-04-19T03:16:36+00:00

I too tried T500. If you bang on column and astutest the column temp. Down/Up & it will make lot's more then they stated on it. First few times only 4 quarts. Last few times made over 6 Quarts 190* & so on. Really depends the pantheists on the wash to be done really. Also i used Benoite to clear it up quickly.

Statistics: Posted by lll_0_mike_0_lll — Fri Apr 19, 2013 3:16 am

Re: T500 water outlet problem

2013-04-19T02:27:38+00:00

I started with a t500 and I love it, makes great consistent 93% neutral and very easy to operate. The one thing that everyone struggles with is the water flow temperature. What you need to realize is that when it starts to produce the temperature of the wash does not stabilize for a few minutes after it starts producing so the temp will fluctuate for the first say 5 minutes and then once it is set it usually stays in the range and then no more adjustments in water flow are necessary. Unless someone flushes the toilet.:-) :-) :-) I also recommend cleaning the ceramics and copper after three or so runs.

Statistics: Posted by edwatters — Fri Apr 19, 2013 2:27 am

Re: T500 water outlet problem

2013-04-19T00:23:19+00:00

I finally just looked at mine and there is only one hole on your second picture for the outflow. On yours i noticed one going back out into the column inside part. That not right at all. Sorry for your troubles but hope you get it all straighten out soon. Not bad peace of hardware to have at all.

Statistics: Posted by lll_0_mike_0_lll — Fri Apr 19, 2013 12:23 am

Re: T500 water outlet problem

2013-04-18T18:55:26+00:00

Next time i take my ceramics out i take a look. I am sure it shouldn't be one there when i looked at my last. BRB with the answer when i can get to mine.

Statistics: Posted by lll_0_mike_0_lll — Thu Apr 18, 2013 6:55 pm

Re: T500 water outlet problem

2013-04-18T15:11:56+00:00

The fact that my wash is coming out of the water outlet is what has me worried..if you look at the pictures I posted on the bottom of the copper coil you can see the nozzle where the water comes out and an additional hole. Idk if that hole is supposed to be there or not.

Statistics: Posted by nitronick60 — Thu Apr 18, 2013 3:11 pm

Re: T500 water outlet problem

2013-04-18T14:14:41+00:00

Perhaps column wasn't packed right copper ones on top then ceramics. Make really sure there not to tight tho. Need have a little play in it. Looked like your column is just fine.

Statistics: Posted by lll_0_mike_0_lll — Thu Apr 18, 2013 2:14 pm

Re: T500 water outlet problem

2013-04-18T02:04:02+00:00

I just wish I had a picture of the coil inside the column to compare mine with

Statistics: Posted by nitronick60 — Thu Apr 18, 2013 2:04 am

Re: T500 water outlet problem

2013-04-18T01:01:02+00:00

Only problems i ever had like that was when mine be running all smoothly. had 6 jars & then stoped it. Was very tired. Whent to start it back up next day & was not coming up to temp at the top unless i cut down the outlet a lot. Due to i think the alcohol was gone to be converted. But that being said. 6 jars or 190 proof is not bad on a single run. Best i ever had so far

Statistics: Posted by lll_0_mike_0_lll — Thu Apr 18, 2013 1:01 am

Re: T500 water outlet problem

2013-04-18T00:02:20+00:00

I sent it back to the brew shop so he can take a look at it. I will let everyone know what he finds out.

Statistics: Posted by nitronick60 — Thu Apr 18, 2013 12:02 am

Re: T500 water outlet problem

2013-04-17T09:21:44+00:00

What I do to post links is left click on the address bar, which then turns blue.

Right click and then left click 'copy' from the drop down menu. To post the link, right click the post you are making and then left click 'paste' from the drop down menu.

Hope this helps.

Statistics: Posted by John51 — Wed Apr 17, 2013 9:21 am

Re: T500 water outlet problem

2013-04-16T23:40:58+00:00

If you Google t500 there is a video that shows how to assemble it correctly, if you think that my bethe problem. I would post the link but I don't know how. Sorry

Statistics: Posted by edwatters — Tue Apr 16, 2013 11:40 pm

Re: T500 water outlet problem

2013-04-16T22:53:27+00:00

There were some pictures of one disassembled on another thread but I could not find it.

Statistics: Posted by nitronick60 — Tue Apr 16, 2013 10:53 pm

Re: T500 water outlet problem

2013-04-16T22:12:26+00:00

Yeah, that doesn't look right, the water should just flow down the tube and out the outlet. It shouldn't be able to escape into the column I'm just trying to find a photo of mine.

Statistics: Posted by MrCat — Tue Apr 16, 2013 10:12 pm